thingiverse
Pottery Vase Ribs
A small collection of Vase Ribs
pottery ribs 3D Models
339 results
thingiverse
thingiverse
Pottery Tools/Ribs
Sometimes you lose the tools, sometimes they just break. Instead of always ordering new...
thingiverse
Pottery Ribs with storage holes
Simple remix of Ooklaboo's designs. I added a 10mm hole at one end so the ribs can be ...
thingiverse
Pottery Bowl Rib
Tip: Print the top and bottom halves separately so that the rounded sides print smooth....
grabcad
Rib/Circular Pattern
This was part of one of my assignments.
thingiverse
Pottery tools: Circular pottery ribs 5 inch 4 inch 3 inch
Pottery ribs, good for bowls, plates.
thingiverse
Dual Sided Pottery Rib Tool
Dual sided rib tool for pottery, both patterns give should give a unique design. This i...
thingiverse
Two Sided Wavy Pottery Rib
A simple rib tool that can be used to wake a wavy or bubbled edge on clay on a pottery ...
thingiverse
Battery connector tower with flanges and ribs
Added a flange for epoxy joining, as well as ribs to reinforce the vertical portion due...
thingiverse
Design by Anne: Pottery Ribs for Mugs, Cups and Steins - multiple styles and sizes
Designs by Anne F.: Various pottery ribs will be added over time. Each one is made 15...
grabcad
Hybride plastic casing
lip/groove, ribs, cut from surface, replace face and sketch driven pattern
grabcad
19 inch Rack Plate
made for screw type racksplate is 9.25 tall with strength ribs on rearused the .625/.62...
thingiverse
VEX robotics - 3000 mAh Battery Holder
Mounting bracket for the standard VEX 7.2V 3000 mAh battery. Battery is held in place ...
thingiverse
Gigabyte A5 Laptop Dummy Cover
For Gigabyte A5 Series Gaming Laptops (Model Nr: AES1130SD , Battery Model Nr: 6-87-nh5...
thingiverse
3S18650 battery holder case
Use some parts on the market, a battery holder for 3S-18650, a BMS board, M3 screws. P...
thingiverse
Samsung Galaxy S8+ Case
Phone Case for Samsung Galaxy S8+. Has ribs on the side to help with grip and a interes...
thingiverse
Rebreather battery holder
A simple 3 battery holder (for the 18650 rechargeable as used on the X-CCR rebreather. ...
prusaprinters
AT Simple switched dice roller for 9 fl oz Solo cup
A remix of bfulton's AT Simple switched dice roller that uses a 266 ml / 9 fl oz clear ...
myminifactory
Pen Holder for HUION Drawing Tablets
Pen/Stylus holder for Huion Battery Pen. The base is a compartment to hold up to 6 repl...
thingiverse
Pen Holder for HUION Drawing Tablets 1rst version
Pen/Stylus holder for Huion Battery Pen. The base is a compartment to hold up to 6 rep...
thingiverse
Pen Holder for HUION Drawing Tablets
Pen/Stylus holder for Huion Battery Pen. The base is a compartment to hold up to 6 rep...
grabcad
Thimble
A redesigned utensil from the sewing box.Created, because it was a good exercise for ax...
thingiverse
Wurlitzer 200 series speaker templates
This is a template for accurately locating the speaker holes on a Wurlitzer 200 series ...
grabcad
Plate
Steps:1. Sketched side profile and revolved to create the base2. Made the first extrude...
grabcad
Plate
Steps:1. Sketched side profile and revolved to create the base2. Made the first extrude...
cgtrader
Nine-Volt Battery Free 3D model
Free Nine-Volt Battery Model No Textures included Available Formats included are FBX, M...
thingiverse
Raspberry Pi 3 (B/B+) Case w/ 40mm Fan
Added options for a 40mm fan for cooling, including a vent down the side. Best used if ...
cults3d
Battery Sled - 1590B - 26650x2
Double-cell 26650 sled for a Hammond 1590B box. Includes support ribs to add strength t...
thingiverse
Battery Sled - 1590B - 26650x2
Double-cell 26650 sled for a Hammond 1590B box. Includes support ribs to add strength t...
grabcad
Antigravity Micro Start Case
Here's my first entry for the Antigravity Challenge @ https://grabcad.com/challenges/an...